Low Voltage Prewire in Los Angeles

Planning a new build or remodel in Los Angeles? Put the low-voltage wiring on the construction schedule before insulation and drywall. We plan cable routes for networking, cameras, speakers, and controls while access is straightforward.

Years in the field

1 +

LA installations

100 +

Company to call for support

Low Voltage Prewire LA

We handle prewire for new construction and remodels across Los Angeles. We coordinate with general contractors, architects, and electricians so the low-voltage rough-in fits the schedule. Cables are labeled at both ends and routed back to a structured wiring panel or rack.

A typical plan includes Cat6 or Cat6A at TV, desk, camera, and access point locations; speaker wire for indoor and outdoor audio; and control wiring for lighting, shades, keypads, and door stations. Fiber and coax are included where the project calls for them.

We also discuss future equipment locations and accessible routes for later additions. A little planning during framing can reduce the need to reopen finished walls.

Structured cabling and low-voltage rough-in

Prewire is also called structured wiring or low-voltage rough-in. It brings data cabling, speaker wire, camera connections, and control wiring back to planned equipment locations. A useful plan shows each Ethernet outlet, ceiling access point, TV connection, and audio zone, along with space for a rack or structured media enclosure.

For a remodel, new home, or commercial tenant improvement, share the floor plan and expected construction dates. We can separate the rough-in work from termination, testing, equipment installation, and final setup so the responsibilities are clear. Our low-voltage prewire checklist helps you prepare those decisions before insulation and drywall.

Wire once, use for decades

Ethernet and fiber pulled during framing outlive the devices they connect to. The wire is the long-term investment; the gear on either end is easy to swap.

Clean labels, clean panel

Every drop numbered, mapped, and terminated in a labeled panel. When someone opens that closet in ten years, they know exactly what’s what.

GC-friendly

We show up when we’re supposed to, protect the work through the rest of the build, and come back for trim-out on schedule.

Gallery

Prewire planning examples

Examples of cable routes, rough-in locations, and wiring panels to consider when planning a new build or remodel.

Easy Prewire Installation

Site walkthrough

We review the plans and walk the property with you or your builder to confirm equipment locations, cable routes, and the construction schedule.

Review the scope

You receive a written scope with cable locations, equipment allowances, and the planned rough-in and trim-out work. We confirm access and coordination requirements before scheduling.

Rough-in and trim-out

We install and label the planned cabling during rough-in, then return at the agreed stage to terminate, test, and finish the connections.

Talk to us about your Low Voltage Needs

Free on-site walkthrough and written quote across Los Angeles and Southern California.

Residential Prewire Los Angeles

Prewire can be part of a full remodel or a single room refresh. When the walls are open, we work with your general contractor to plan the cable drops you need now and the locations you may want later.

The scope starts with your floor plan and equipment locations, so you can see what will be installed before the work begins.

Prewire is perfect for camera locations at every entry, perimeter, driveway, and gate.
Ethernet drops behind every TV and at every desk.
Speaker wire in the ceiling of any room you’d want music in.

Get In Touch

Ready to transform your home? Contact us for a free consultation and demo

Send us a message

Phone

(323)329-4737
Available 24/7 for emergencies

Email

info@hardwiredav.com
We'll respond within 24 hours

Location

Los Angeles, California
Serving all of Southern California

Business Hours

Open 24 hours, 7 days a week

Low Voltage Prewire FAQs

When in the build should we prewire?

Bring us in during design or early framing so cable routes and equipment locations can be coordinated with the builder. The rough-in normally happens before insulation and drywall, with timing agreed around the other trades. We also plan the later trim-out, termination, and testing stages.

What should I prewire for even if I'm not installing it yet?

Start with the equipment you realistically expect to add: access points, TV and desk locations, cameras, speakers, shades, or a gate intercom. We review the floor plan, cable routes, and space for a wiring panel or rack. Spare cable or an accessible pathway can make later additions easier without committing you to every device now.

Do you coordinate with the general contractor?

Yes. We schedule around the trades, protect our work through the rest of the build, and come back for trim-out at the right stage.

What cable do you use?

Cat6 or Cat6A for networking, speaker cable sized for the run and equipment, and control cable where the selected system needs it. Some projects also need coax or fiber. We choose cable for the distance, installation environment, and equipment requirements, then label and test the finished connections.

Can we prewire during a remodel too?

Yes. Any time drywall is open is a chance to add wire. We do full remodels and single-room refreshes.

Does prewire lock us into your company for the finish?

No. We document everything so any qualified integrator can pick up the trim-out. Most of our prewire clients bring us back because the transition is easier, not because they're locked in.

What affects the cost of low-voltage prewire?

The number and length of cable runs, access, cable type, panel or rack requirements, and the work included at trim-out all affect the price. A floor plan and construction schedule help us prepare a useful scope. We identify rough-in, termination, testing, and any equipment included in the written quote.